Energy
A. Hemmati; T. Abedzadegan
Volume 16, Issue 1 , March 2019, , Pages 70-83
Abstract
Different methods of urban sewage sludge energy recovery such as burning, gasification, pyrolysis and digestion based on the net energy production efficiency, advantages and disadvantages and complexity of these processes have been investigated in this article. The best method for energy production from ...
Read More
Different methods of urban sewage sludge energy recovery such as burning, gasification, pyrolysis and digestion based on the net energy production efficiency, advantages and disadvantages and complexity of these processes have been investigated in this article. The best method for energy production from sludge was selected among different methods according to energy and the amount of the greenhouse gas production. The capacity of the constructed power plant was calculated and investigated economically for each scenario. Quantitative and qualitative information on sludge was required to carry out this research so Ekbatan wastewater treatment sludge was analyzed. The results showed that the sludge of this treatment plant has 5.7% solids, containing 65.7% volatiles and the dry heat value is about 15100 kJ/kg. It was found that the best scenario for sludge energy production in this treatment plant is a digestion process with pure net energy production of 73.2 × 107 kJ/d. The energy recovery in an anaerobic digester can prevent the emission of 16,680 tons of CO2 annually and release about 1,460 tons of CO2 per year. The chemical analysis shows that the selected sludge has a potential production of 25m3 of CH4 for each m3 of sludge. The annual amount of biogas that can be recovered from municipal treatment plant is 836543 m3. On the other hand, the biogas can be used to generate electricity. The power of the plant is about 216.8 kW that with the construction of this power plant, an annual saving of 1.5 million dollars will occur.
Energy
E. GhasemiKafrudi; M. Amini; M. R. Habibi
Volume 14, Issue 4 , December 2017, , Pages 32-47
Abstract
The effects of greenhouse gases (GHG) on the growth of global warming, and increase of GHG and air pollutant emissions for energy production have forced the need of energy recovery which is normally wasted in industrial plant. The present research work focused on the GHG and air pollutant emissions reduction ...
Read More
The effects of greenhouse gases (GHG) on the growth of global warming, and increase of GHG and air pollutant emissions for energy production have forced the need of energy recovery which is normally wasted in industrial plant. The present research work focused on the GHG and air pollutant emissions reduction employing pressure waste energy recovery. Pressure break-down via Joule-Thomson valve is a neat potential for waste energy recovery in gas refineries, which may also be provide by using a turbo-expander instead of commercial valves. Based on this ground, an exergy analysis is carried out for Joule-Thomson valve. The results showed that the exergy loss is higher than 6.5 MW and it is possible to recover about 1.9 MW of exergy loss. On the other hand, it was found that about 16900MWh of electrical energy can be produced by recovering the energy of waste pressure, which may leads to less consumption of the load and gas in refinery power unit. Consequently, equal the gas consumption reduction, 12056 ton CO2e of GHG and 54.6 ton of air pollutant emissions is reduced annually. Economical evaluation of utilizing a turbo-expander instead of a valve proved that this altering scenario is deducible and practical. Economical indexes, namely, IRR and NPV are found to be equal to 25.51% and 929571 US$, respectively. Moreover, sensitivity analysis conducted on each specific state certified the obtained results.
Transport Phenomena,
Leila Omidvar Langroudi; hassan pahlavanzadeh; sara nanvakenari
Volume 13, Issue 4 , November 2016, , Pages 96-112
Abstract
This study introduces an experimental and theoretical investigation of the performance of a proposed air dehumidification system using a nanofluid of γ-alumina nano-particles in LiBr/H2O as a desiccant. Comparative experiments organized using a central composite design were carried out to evaluate ...
Read More
This study introduces an experimental and theoretical investigation of the performance of a proposed air dehumidification system using a nanofluid of γ-alumina nano-particles in LiBr/H2O as a desiccant. Comparative experiments organized using a central composite design were carried out to evaluate the effects of six numerical factors (air velocity, desiccant flow rate, air humidity ratio, desiccant solution concentration, air temperature, desiccant temperature) and one categorical factor (adding nano-particles) on outlet air humidity ratio and outlet air temperature as responses. Reduced quadratic models were derived for each response. The results revealed that the concentration of LiBr/H2O solution and air temperature had the largest effect on outlet air humidity ratio and outlet air temperature, respectively. It was found that the average increase in mass transfer rate was 12.23% and heat transfer rate was 13.22% when γ-alumina nano-particles (0.02% wt) were added to the LiBr/H2O solution. The average increase in mass transfer coefficient was 22.73% and heat transfer coefficient was 26.51%.